Plumbing Basics: A Must for Installing a Bathtub
Plumbing Basics: A Must for Installing a Bathtub
Blog Article
Listed here below you will discover a good deal of first-rate resources in regards to Installing A Bathtub.
Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and also often, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is readily obtainable, the job can move immediately; if you need to open up a wall to eliminate the old bathtub and position the new bathtub, the task is a lot harder. In either situation, the project is within a home handyman's skills, although you will certainly need an assistant to move out the old tub and also embeded in the brand-new one. Ensure you have certified on your own for the task and also fit trying it. As opposed to working with a professional to take over a halfway-completed project, it is better to consider employing one before you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly assist you install a brand-new tub in your restroom if you have currently gotten a new bathtub as well as do not require to change the setup of your previous water system pipes.
Your devices and product checklist need to make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, after that the first thing you should do is detach the water system. After doing so, switch on the taps to drain any water staying in the system. The process of removing the existing faucets can be quite problematic as a result of the restricted access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines are in place in between the tap and also the sink. Protect the tap in position with the producer provided backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type should be attached to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bathtub up until the level reads level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water supply as well as check all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as also examine the overflow outlet as well as the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been made use of at the very least when as this will resolve it into its final placement.
Getting ready for the Installation
To start with, the supporting frame provided with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its last position.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, triggering the water to pass through the wall in between the bathroom and also the tiling, bring about problems with dampness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bathtub with water before securing, to enable the movement experienced when the bathtub is in use. The sealant can break relatively early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader about Tools You Need to Install a New Bathtub , I thought sharing that piece of content was important. Sharing is good. Who knows, you may just be doing someone a favor. I value reading our article about How to Install a Bathtub.
Get A Free Estimate Report this page